SmartgridOne logo
SmartgridOne logo
Accessories
AppCertificates
Configuration from A to Z
Control response timeController
Customer Specific
Devices
Boiler
Cloud
Energy Meter
Ev Charging Station
Gas Meter
Heat Pump
New integrations
Plc
Pv Hybrid And Battery Inverters
a-TroniXABB, FIMERADS-TecAforeAlphaESSAmpowrAngileAnklous PV, Hybrid and Battery InvertersAPsystemsAteps Battery
Autarco
BeauventC-BatteryCellpowerChisageDanfossDeltaDET Power PV, Hybrid and Battery InvertersDEYEDiehl-AkoDMEGC InvertersDynessDysun EnergyEcosourcenEenovanceElecnovaEnbrilionEnergreenEnerlutionEnjoyPowersEnphaseEP EquipmentESY InvertersEVEFortona
Foxess
FraxFroniusGoodWeGotionGreener / Alfen
Growatt
HiteHithium
Huawei
Hypontech
Hyxipower
iWellJinkoKacoKehuaKostal
Kstar
MarstekMastervoltMidTeQMotomaOctave EnergyOmniPowerPixiiPower-SonicPoweroadPylontechRefurbRegitecRenonRitarSAJSchneider SunEzySchucoSCUSE2200H till SE6000HSessySigenergySinexcel
Sma
Socomec
Sofar
Solaredge
SolarlogSolarMaxSolarwattSolaxSolinteg
Solis
Solplanet
Sungrow
SunwaytechSunwoda
Sunwoda
Sus-PowerTeclomanTeploreTesvoltVaconVictronVolstoraWattsNextWeihengXantrexZendure SolarFlowZetaraZeversolar
Switched Loads
Water Meter
External Signals
InstallationLicenseNetworkQuick StartSafety, maintenance and legal noticesSpecificationsStatus LEDs
Toolbox
Troubleshooting
Video tutorialsWiring & connectivity guidelines
DevicesPv Hybrid And Battery Inverters
logo

KACO Inverters

Supported Devices

Device TypeVariantsModbus TCP (Ethernet)RS485Curtailment
blueplanet TL350.0 / 60.0✅❌✅
87.0 / 92.0 / 105.0🔶 (specific software required)
Warning
Warning

Curtailment of the blueplanet TL3 87.0 / 92.0 / 105.0 inverters is only possible with software version V03-59-REL-03aaf518 or newer. You can check the software version of the inverter under the "info" tab.

KACO software version

Wiring

The SmartgridOne Controller and the Kaco inverters communicate via Ethernet.

Ethernet

For correct ethernet wiring: Follow the the guidelines for ethernet wiring.

Configuration

blueplanet 50.0 / 60.0 TL3

Modbus Write access must be enabled in the settings of the inverter:

  1. Log in to the interface of the inverter on the local Network
KACO blueplanet 50.0/60.0 Interface login
  1. Go to Interfaces and Network Services
KACO blueplanet 50.0/60.0 Interface menu
  1. Enable the "Modbus TCP Write access" setting
KACO blueplanet 50.0/60.0 Interface setting

blueplanet 92.0 / 105.0 TL3

Modbus Write access must be enabled in the settings of the inverter:

  1. Log in to the interface of the inverter on the local Network
  2. Go to Interfaces and then Network Services
  3. Enable both the "Modbus TCP/UDP Read access" and "Modbus TCP/UDP Write access" settings
KACO blueplanet 92.0 / 105.0 Interface setting

Jinko

Previous Page

Kehua

Next Page

On this page

KACO InvertersSupported DevicesWiringEthernetConfigurationblueplanet 50.0 / 60.0 TL3blueplanet 92.0 / 105.0 TL3