SmartgridOne logo
SmartgridOne logo
App
Externe Signale
Fehlerbehebung
Geräte
Cloud
Energiezähler
Gaszähler
Geschaltete Lasten
Kessel
Ladestation für Elektrofahrzeuge
Neue Integrationen
Plc
Pv-Hybrid- und Batteriewechselrichter
a-TroniXABB, FIMERADS-TecAforeAlphaESSAmpowrAngileAnklous PV, Hybrid- und BatteriewandlerAPsystemsAteps-Batterie
Autarco
BeauventC-BatterieCellpowerChisageDanfossDeltaDET Power PV, Hybrid- und BatteriespeicherwechselrichterDEYEDiehl-AkoDMEGC WechselrichterDynessDysun EnergyEcosourcenEenovanceElecnovaEnbrilionEnergreenEnerlutionEnjoyPowersEnphaseEP-AusrüstungESY-WechselrichterFortona
Foxess
FraxFroniusGoodWeGotionGreener / Alfen
Growatt
HiteHithium
Huawei
Hypontech
Hyxipower
All In One ESSHybrid Inverters
iWellJinkoKacoKehuaKostal
Kstar
MarstekMastervoltMidTeQMotomaOctave EnergieOmniPowerPixiiPower-SonicPoweroadPylontechRegitecRenonRenovierungRitarSAJSchneider SunEzySchucoSCUSE2200H bis SE6000HSessySigenergySinexcel
Sma
Socomec
Sofar
Solaredge
SolarlogSolarMaxSolarwattSolaxSolinteg
Solis
Solplanet
Sungrow
SunwaytechSunwoda
Sunwoda
Sus-PowerTeclomanTeploreTesvoltVaconVictronVolstoraWattsNextWeihengXantrexZeversolar
Wärmepumpe
Wasserzähler
Installation
Konfiguration von A bis Z
Kundenspezifisch
LizenzNetzwerkSchnellstartSicherheits-, Wartungs- und RechtshinweiseSpezifikationenStatus-LEDsSteuerantwortzeitSteuerungVerdrahtungs- und AnschlussrichtlinienVideo-Tutorials
Werkzeugkasten
Zertifikate
Zubehör
GerätePv-Hybrid- und BatteriewechselrichterHyxipower
logo

Unterstützte Geräte

Device TypeVariantsManualModbus TCP (Ethernet)RS485Curtailment
All In One ESSHYX-H6K-HTAManual❌✅✅
HYX-H9K-HTA
HYX-H12K-HTA
HYX-H15K-HTA

Verkabelung

RS485

Hyxipower

Previous Page

Hybrid Inverters

Next Page

On this page

Unterstützte GeräteVerkabelungRS485

Für die RS485-Verkabelung verwenden Sie den COM-Port (Nr. 5) am Wechselrichter.

Info
RS485 Wiring
  • For correct RS485 wiring: Follow the guidelines for RS485 wiring.
  • If the wiring shown in the table below is incorrect, please let us know.
  • There is no general consensus in the industry about the usage of A and B for the RS485 polarity, so it may be counterintuitive and opposite of what you might expect for some devices.
DeviceSmartgridOne Controller model OM1SmartgridOne Controller model IG8RS485-USB converterRS485-Ethernet converter
RS485 A (Pin 5)RS485 ARS485_POSRS485 ATX+
RS485 B (Pin 6)RS485 BRS485_NEGRS485 BTX-
N/ARS GNDGNDNot availableG
Warnung
NOTE: RS485 Device Addresses
  • You MUST give each device on the RS485 bus a unique address. Check the manual of the device on how to do this.
  • Use lower addresses first (1, 2, ...) because the SmartgridOne Controller will find them faster!
  • For each device, it is generally recommended to stick with the factory default baud rate, parity, and stop bits. The SmartgridOne Controller will scan on those first.